Manufacturer of Membrane Process - UF Membrane Module 8 inch PVDF Ultrafiltration Membrane Module UFf200 Circuit Board Waste Water Treatment – Bangmo
Manufacturer of Membrane Process - UF Membrane Module 8 inch PVDF Ultrafiltration Membrane Module UFf200 Circuit Board Waste Water Treatment – Bangmo Detail:
Applications
Drinking water treatment of tap water, surface water, well water and river water.
Pretreatment of RO.
Treatment, recycle and reuse of industrial waste water.
Filtration Performance
This product is proven to have below filtering effects according to the service conditions of different water sources:
| Ingredient | Effect |
| SS, Particles > 1μm | Removal Rate ≥ 99% |
| SDI | ≤ 3 |
| Bacteria, Viruses | > 4 log |
| Turbidity | < 1NTU |
| TOC | Removal Rate: 0-25% |
*Above data is obtained under the condition that feeding water turbidity is < 25NTU.
Product Parameters
Technical Parameters
| Filtering Type | Outside-in |
| Membrane Material | Modified PVDF |
| MWCO | 200K Dalton |
| Membrane Area | 47m2 |
| Membrane ID/OD | 0.8mm/1.3mm |
| Dimensions | Φ200mm*1710mm |
| Connector Size | DN50 Clamping |
Application Data
| Pure Water Flux | 9,400L/H (0.15MPa, 25C) |
| Designed Flux | 40-120L/m2.hr (0.15MPa, 25C) |
| Suggested Working Pressure | ≤ 0.2MPa |
| Maximum Transmembrane Pressure | 0.15MPa |
| Maximum Backwashing Pressure | 0.15MPa |
| Air Washing Volume | 0.1-0.15N m3/m2 .hr |
| Air Washing Pressure | ≤ 0.1MPa |
| Maximum Working Temperature | 45C |
| PH Range | Working: 4-10; Washing: 2-12 |
| Operating Mode | Cross-flow or Dead-end |
Feeding Water Requirements
Before feeding water, a security filter < 50 μm should be set to prevent blockage caused by large particles in raw water.
| Turbidity | ≤ 25NTU |
| Oil & Grease | ≤ 2mg/L |
| Suspended Solids | ≤ 20mg/L |
| Total Iron | ≤ 1mg/L |
| Continuous Residual Chlorine | ≤ 5ppm |
| COD | Suggested ≤ 500mg/L |
*Material of UF membrane is polymer organic plastic, there must not be any organic solvents in raw water.
Operating Parameters
| Backwashing Flow Rate | 100-150L/m2.hr |
| Backwashing Frequency | Every 30-60min. |
| Backwashing Duration | 30-60s |
| CEB Frequency | 0-4 times per day |
| CEB Duration | 5-10min. |
| CIP Frequency | Every 1-3 months |
| Washing Chemicals: | |
| Sterilization | 15ppm Sodium Hypochlorite |
| Organic Pollution Washing | 0.2% Sodium Hypochlorite + 0.1% Sodium Hydroxide |
| Inorganic Pollution Washing | 1-2% Citric Acid/0.2% Hydrochloric Acid |
Component Material
| Component | Material |
| Membrane | Modified PVDF |
| Sealing | Epoxy Resins |
| Housing | UPVC |
Product detail pictures:
Related Product Guide:
We keep on with the basic principle of quality to start with, support very first, continuous improvement and innovation to meet the customers for your management and zero defect, zero complaints as the quality objective. To great our service, we offer the items with all the superior high quality at the reasonable selling price for Manufacturer of Membrane Process - UF Membrane Module 8 inch PVDF Ultrafiltration Membrane Module UFf200 Circuit Board Waste Water Treatment – Bangmo , The product will supply to all over the world, such as: Uruguay, Sacramento, Panama, We have exported our products all over the world, especially the USA and European countries. Furthermore, all of our products are manufactured with advanced equipment and strict QC procedures to ensure high quality.If you are interested in any of our products, please don't hesitate to contact us. We will try our to meet your needs.
By Julia from Kenya - 2018.12.30 10:21
Product quality is good, quality assurance system is complete, every link can inquire and solve the problem timely!
By Iris from Kenya - 2018.12.05 13:53
Write your message here and send it to us
